logo
Cases Details
Home / Cases /

Company cases about 12m Tube Laser Bevel Cutting Replaces Saw and Chamfering on Thick Wall Structural Tube

12m Tube Laser Bevel Cutting Replaces Saw and Chamfering on Thick Wall Structural Tube

2026-11-09

Application case — thick wall tube, structural and heavy equipment members

When the wall thickness passes about 8mm, the economics of tube fabrication change. Saw kerf becomes material loss, chamfering becomes a slow manual operation, and handling a 12m member twice adds risk as well as time. This case describes a thick wall structural application where a 12m tube laser with a 0-45° bevel head replaces both the saw and the chamfering station.

latest company case about 12m Tube Laser Bevel Cutting Replaces Saw and Chamfering on Thick Wall Structural Tube  0

Project snapshot

Industry Crane booms, agricultural machinery frames, heavy equipment chassis
Material Carbon steel square and round tube, 6-16mm wall
Machine QH-12022GB tube laser cutting machine
Configuration 12000mm loading length, 220mm chuck, 12000W fiber source, 0-45° bevel cutting head
Parts involved Boom chords, chassis rails, truss diagonals, bracket saddles

The process problem

  • Saw kerf is real money. A bandsaw removes a few millimetres per cut. On thick wall tube that is both material loss and a squareness that still needs correction before welding.
  • Chamfering thick wall is slow and physical. A 12-16mm chamfer by grinder or portable milling machine is an operator-bound operation, and the result depends on how tired the operator is at the end of the shift.
  • Long members accumulate error. Cutting a 12m rail in two setups means the hole pattern references two datums, and that shows up as fit-up problems at the far end of the assembly.
  • Handling risk. Every additional move of a 12m heavy member is a crane lift and a chance of damage or injury.

Process comparison

Step Conventional route With QH-12022GB
Cut to length Bandsaw, kerf loss, then square up Laser cut, negligible kerf, square in one pass
Chamfer / bevel Grinder or portable mill on thick wall 0-45° V or Y bevel by the cutting head
Holes and copes Drill line, or separate coping station Cut in the same cycle
Datum Two setups on a 12m member One clamping, one datum
Crane lifts per member Three or more Load, unload
Repeatability Operator dependent Program dependent

What changes on the shop floor

  • Full 12m processing. Commercial tube length is loaded once. The mid cut, the re-chuck and the second datum disappear from the route.
  • One datum for the whole member. Hole positions, copes and bevels are all referenced to a single clamping, which is what keeps a four piece boom assembly closing square.
  • 12000W on thick wall. The source pierces and cuts 12-16mm carbon steel with a clean edge, so the post-cut grinding that thick plate work normally demands is reduced.
  • Bevel on 220mm sections. The rotary axis and head interpolate the bevel around large square and round sections, holding a uniform chamfer where manual grinding drifts.
  • Fewer lifts, less risk. Two crane lifts per member instead of three or more — a safety gain that matters more than the time saving on heavy work.

Where the limits are

This configuration accepts tube up to 220mm, loads 12m, and cuts 0.5-16mm carbon steel and 0.5-10mm stainless. Bevel range is 0-45°. Work outside those limits — larger sections or heavier wall — needs a different chuck and power combination, and should be specified from the drawing rather than assumed.

Who this fits

Structural fabricators, crane and agricultural equipment builders, and chassis manufacturers cutting thick wall tube in long lengths, where the weld preparation is on the critical path and where every extra handling step carries both cost and risk.

Machine used in this case

QH-12022GB 12000mm 220mm Chuck Bevel Cutting Tube Laser Cutting Machine 12000W — 12m loading, 220mm chuck, 12000W fiber source, 0-45° bevel cutting head.