logo
Cases Details
Home / Cases /

Company cases about Bevel Cutting on a 6m Tube Laser Removes the Chamfering Step for Thin Wall Guardrail Tube

Bevel Cutting on a 6m Tube Laser Removes the Chamfering Step for Thin Wall Guardrail Tube

2026-11-09

Application case — thin wall tube, guardrail and furniture frames

Guardrail, shelving and fitness equipment makers cut a lot of 6m tube, and almost every part needs an end preparation before welding. In most shops that preparation is a three step route: saw cut to length, deburr, then grind or machine a chamfer. Each step needs a person, a fixture and a handling move, and the angle lives in the operator's hands rather than in the drawing. This case describes how a 0-45° bevel cutting head on a 6m tube laser removes that third step from the route.

latest company case about Bevel Cutting on a 6m Tube Laser Removes the Chamfering Step for Thin Wall Guardrail Tube  0

Project snapshot

Industry Guardrail, shelving, fitness equipment frames
Material Carbon steel square, rectangular and round tube, 1.5-3mm wall
Machine QH-6016GB tube laser cutting machine
Configuration 6000mm loading length, 160mm chuck, 6000W fiber source, 0-45° bevel cutting head
Parts involved Frame posts, cross rails, brackets, corner joints

The process problem

On thin wall tube the chamfering step is the weakest link in the route for three reasons.

  • Angle depends on the operator. A hand grinder produces a slightly different chamfer on the first and the hundredth part, and a fit-up that needs extra weld wire hides the difference instead of fixing it.
  • Extra handling deforms thin wall. Every move from saw to deburr to grinding bench is a chance to dent a 1.5mm wall, particularly on long rails.
  • Changeover cost. A new tube profile usually means a new fixture and a new grinding setup, so small mixed batches are the least profitable work in the shop.

Process comparison

Step Conventional route With QH-6016GB
Cut to length Bandsaw or cold saw Laser cut in the same program
Deburr Manual or bench machine Not required (laser edge)
Chamfer / bevel Grinder or dedicated chamfering machine 0-45° V or Y bevel produced by the cutting head
Holes and slots Drill station or punch press Cut in the same cycle
Clampings per part Two to three One
Angle source Operator judgement Program value, repeatable

latest company case about Bevel Cutting on a 6m Tube Laser Removes the Chamfering Step for Thin Wall Guardrail Tube  1

What changes on the shop floor

  • One clamping, complete part. Profile, holes, slots and bevel are generated from the same tube model, so the part leaves the table ready for fit-up rather than ready for the grinding bench.
  • Bevel follows the profile. Because the rotary axis and the cutting head interpolate together, the chamfer stays uniform on square, rectangular and oval sections — the geometry a hand grinder cannot follow.
  • Thin wall stays flat. Cutting instead of grinding means no mechanical pressure on the wall, and 6000W with tuned piercing parameters keeps heat input low enough to avoid the discoloration that shows through powder coating.
  • Changeover becomes a program recall. Switching from 40x40 square tube to 60mm round tube is a stored program, not a fixture rebuild, which makes short mixed batches viable.
  • Full 6m loading. Long rails are cut in one clamping, so hole-to-hole and end-to-end dimensions reference a single datum instead of accumulating error across two setups.

Where the limits are

Being precise about the envelope matters more than a sales claim. On this configuration the chuck accepts tube up to 160mm, the bevel range is 0-45°, and practical wall thickness is roughly 0.5-10mm in carbon steel and 0.5-6mm in stainless. Work above those limits belongs to a 220mm chuck machine with a higher power source, which is a separate model in the same range.

Who this fits

Fabricators producing guardrails, shelving, shop fittings, fitness frames and light structural bracing from 6m stock, where the part count is high, the wall is thin, and the weld joint needs a consistent chamfer rather than a fast one.

Machine used in this case

QH-6016GB 6000mm 160mm Chuck Bevel Cutting Tube Laser Cutting Machine 6000W — 6m loading, 160mm chuck, 6000W fiber source, 0-45° bevel cutting head.